TJ torque values and Fluid capacities.

Florpro

Florpro

Well-known member
I think this is where this needs to be.
I am tired of searching the net to find out how to torque my Lugnuts etc. on my TJ I think we should start a sticky with all the torque values on every nut on our jeeps! I will let the mods take it from here and of course all of our members to supply those values.
 
Body Mounts (Main floor to frame) X6 50 ft. lbs. 3/4
Lug nuts 85-110 ft. lbs. 3/4
Transfer case skid bolts 55 ft. lbs. 19mm
Transfer case rear yolk 150 ft. lbs. 1 1/8
A/C Compressor Bracket to Engine Bolts 25 ft. lbs.
A/C Compressor Mounting Bolts 20 ft. lbs.
A/C Low Pressure Service Valve Nut 28 ft. lbs.
Block Heater Nut 16 in. lbs.
Body Mounts (Radiator to frame) X1 35 ft. lbs.
Body Mounts (Rear floor to frame) X4 35 ft. lbs.
Brake bleeder 23 ft. lbs.
Brake caliper mounting bolt 11 ft. lbs.
Bumper (Front) to frame 77 ft. lbs.
Bumper (Rear) to frame 50 ft. lbs.
Camshaft Sprocket Bolt 50 ft. lbs.
Camshaft Thrust Plate to Cylinder Block Screws 18 ft. lbs.
Clutch Cover to Flywheel Bolts 40 ft. lbs.
Coil Bracket to Block Bolts 192 in. lbs.
Connecting Rod Nuts 33 ft. lbs.
Cylinder Block Drain Plugs 25 ft. lbs.
Cylinder Head Bolts 100 ft. lbs.
Cylinder Head Cover Bolts 85 in. lbs.
Differential cover 30 ft. lbs.
Differential cover 30 ft. lbs.
Differential fill plug 25 ft. lbs.
Differential fill plug 25 ft. lbs.
Distributer Clamp Bolt 204 in. lbs.
Drag link Ball studs 55 ft. lbs.
Drag Link clamp 20 ft. lbs.
Driveshaft to axel 14 ft. lbs.
Driveshaft to Transfer case 20 ft. lbs.
Engine Mounts - Front Support Bracket Bolts 45 ft. lbs.
Engine Mounts - Front Support Cushion Bolts/Nuts 30 ft. lbs.
Engine Mounts - Front Support Cushion Bracket Bolts 40 ft. lbs.
Engine Mounts - Front Support Cushion Bracket Stud Nuts 30 ft. lbs.
Engine Mounts - Front Support Cushion Thru-Bolt 48 ft. lbs.
Engine Mounts - Rear Crossmember-to-Sill Bolts (Automatic) 30 ft. lbs.
Engine Mounts - Rear Insulator Stud Assembly Nut 30 ft. lbs.
Engine Mounts - Rear Support Cushion/Bracket Nuts (Manual) 55 ft. lbs.
Engine Mounts - Rear Support Cushion/Crossmember Nuts 192 in. lbs.
Exhaust Manifold/Pipe Nuts 20 ft. lbs.
Flywheel to Converter Housing Bolts 28 ft. lbs.
Flywheel to Crankshaft Bolts 105 ft. lbs.
Front Cover-to-Block Bolts ?-20 60 in. lbs.
Front Cover-to-Block Bolts 5/16-18 192 in. lbs.
Fuel Rail Bolts/Stud 108 in. lbs.
Gas Tank Skid to frame 11.5 ft. lbs.
Gas Tank straps 3 ft. lbs.
Generator Fixed Bolt 18 ft. lbs.
Generator Thru Bolt/Nut 28 ft. lbs.
Lower Control Arms (Front) @ Axle 85 ft. lbs.
Lower Control Arms (Front) @ Frame 130 ft. lbs.
Lower Control Arms (Rear) @ Axle 130 ft. lbs.
Lower Control Arms (Rear) @ Frame 130 ft. lbs.
Main Bearing Brace Nuts 35 ft. lbs.
Main Bearing Cap Bolts 80 ft. lbs.
Oil Filter 156 in. lbs.
Oil Filter Adapter Bolts 75 ft. lbs.
Oil Filter Connector (to adapter) 35 ft. lbs.
Oil Filter Connector (to block) 50 ft. lbs.
Oil Galley Plug 30 ft. lbs.
Oil Pan ?-20 Bolts 84 in. lbs.
Oil Pan 5/16-18 Bolts 132 in. lbs.
Oil Pan Drain Plug 25 ft. lbs.
Oil Pump Cover Bolts 70 in. lbs.
Oil Pump Long Attaching Bolts 204 in. lbs.
Oil Pump Short Attaching Bolts 204 in. lbs.
Pitman Arm nut 185 ft. lbs.
Power Steering Pump Pressure Hose Nut 38 ft. lbs.
Rocker Arm Assembly-to-Cylinder Head Capscrews 21 ft. lbs.
Shock Mounts (Front) @ Lower mount 21 ft. lbs.
Shock Mounts (Front) @ Upper mount 17 ft. lbs.
Shock mounts (Rear) @ Lower mount 74 ft. lbs.
Shock Mounts (Rear) @ Upper mount 23 ft. lbs.
Spark Plugs 27 ft. lbs.
Spedo Sensor 20 in/lbs
Starter Motor Mounting Bolts 33 ft. lbs.
Steering stabilizer @ Draglink 55 ft. lbs.
Steering stabilizer @ frame 55 ft. lbs.
Sway Bar (Front) @ Lower mount 70 ft. lbs.
Sway Bar (Front) @ Upper mount 45 ft. lbs.
Sway Bar (Front) retaining bolts top 40 ft. lbs.
Sway Bar (Rear) @ Lower mount 40 ft. lbs.
Sway Bar (Rear) @ Upper mount 40 ft. lbs.
Thermostat Housing Bolts 156 in. lbs.
Throttle Body Bolts 90 in. lbs.
Tie Rod clamps 20 ft. lbs.
Tie Rod end (ball stud) 65 ft. lbs.
Tie Rod end (to hub) 55 ft. lbs.
Track Bar (Front) @ Axle 55 ft. lbs.
Track Bar (Front) @ Frame 110 ft. lbs.
Track Bar (Rear) @ Axle 74 ft. lbs.
Track Bar (Rear) @ Frame 74 ft. lbs.
Track Bar Ball stud nut (Front) 65 ft. lbs.
Transfer case drain plug 15-20 ft. lbs.
Transfer case fill plug 15-20 ft. lbs.
Transfer case front yolk 150 ft. lbs.
Transmission drain plug 14-20 ft. lbs.
Transmission fill plug 14-21 ft. lbs.
Transmission Support Adapter Bracket Bolts (2WD Auto) 55 ft. lbs.
Transmission Support Bracket Bolt (Manual) 34 ft. lbs.
Transmission Support Bracket/Cushion Bolt (4WD Auto) 55 ft. lbs.
Upper Control Arms (Front) @ Axle 55 ft. lbs.
Upper Control Arms (Front) @ Frame 55 ft. lbs.
Upper Control Arms (Rear) @ Axle 55 ft. lbs.
Upper Control Arms (Rear) @ Frame 55 ft. lbs.
Vibration Damper Bolts 80 ft. lbs.
Water Pump/Block Bolts 17 ft. lbs.
Yolk (Front) @ Axle ???
Yolk (Front) nut @ Transfer case 110 ft. lbs.
Yolk (Rear) @ Axle ???
Yolk (Rear) nut @ Transfer case 120 ft. lbs.
Yolk Straps (Front) @ axle 14 ft. lbs.
Yolk Straps (Front) @ Transfer case 20 ft. lbs.
Yolk Straps (Rear) @ axle 14 ft. lbs.
Yolk Straps (Rear) @ Transfer case ???
 
Engines.
2.5L 4 cyl - 4 quarts
2.4L 4 cyl - 5 quarts
4.0L 6 cyl - 6 quarts

Transmissions.
30RH 3 speed auto - ATF+4 (ATF+3 originally recommended; ATF+4 is replacement).
32RH 3 speed auto- Approximately 4 quarts ATF+4 (ATF+3 originally recommended; ATF+4 is replacement) when drained via dropping the pan / Approximately 8 quarts dry fill.
42RLE 4 speed auto- Approximately 4 quarts ATF+4 when drained via dropping the pan / Approximately 8.8 quarts dry fill
AX-5 5 speed manual - 3.3 quarts 75W-90 GL3, 75W-90 GL4, or 10W30 (NOT GL5 or GL5 compatible as incorrectly stated in some of the manuals)
AX-15 5 speed manual - 3.32 quarts 75W-90 GL3, 75W-90 GL4, or 10W30 (NOT GL5 or GL5 compatible as incorrectly stated in some of the manuals)
NV3550 5 speed manual - 2.1 quarts Mopar fluid part #04874464AA or Synchromax (meets Mopar MS-9224 specs)
NV1500 5 speed manual - 2.4 quarts Mopar part #04874464AA or Synchromax (meets Mopar MS-9224 specs)
NSG370 6 speed manual - 1.58 quarts Mopar part #04874464AA or Synchromax (meets Mopar MS-9224 specs)

T Case
231 - 1.1 quarts ATF+3 or ATF+4
241 - 2.1 quarts ATF+4
Axles
The 231 and 241 transfer cases are fine with any type of good quality ATF. Mercon, Dexron, ATF+4, etc. are all fine. Only the automatic transmission is fussy about the type of ATF it gets.

Axles
Dana 30 - 1.25 quarts 80W-90 or 75W-140
Dana 35 - 1.75 quarts 80W-90 or 75W-140 *
Dana 44 - 2 quarts 80W-90 or 75W-140 *
Rubicon Dana 44 (FRONT) - 1.375 quarts 75W-140 synthetic
Rubicon Dana 44 (REAR) - 2 quarts 75W-140 synthetic **

*4 oz of friction modifier is required with Trac-Lok limited slip differential.
**Friction modifier is NOT required with Tru-Lok locker/limited slip differential (factory Rubicon locker).

Cooling
2.5L - 9 quarts
2.4L - 10.1 quarts
4.0L - 10.5 quarts



 
G Beasley said:
Body Mounts (Main floor to frame) X6 50 ft. lbs. 3/4
Lug nuts 85-110 ft. lbs. 3/4
Transfer case skid bolts 55 ft. lbs. 19mm
Transfer case rear yolk 150 ft. lbs. 1 1/8
A/C Compressor Bracket to Engine Bolts 25 ft. lbs.
A/C Compressor Mounting Bolts 20 ft. lbs.
A/C Low Pressure Service Valve Nut 28 ft. lbs.
Block Heater Nut 16 in. lbs.
Body Mounts (Radiator to frame) X1 35 ft. lbs.
Body Mounts (Rear floor to frame) X4 35 ft. lbs.
Brake bleeder 23 ft. lbs.
Brake caliper mounting bolt 11 ft. lbs.
Bumper (Front) to frame 77 ft. lbs.
Bumper (Rear) to frame 50 ft. lbs.
Camshaft Sprocket Bolt 50 ft. lbs.
Camshaft Thrust Plate to Cylinder Block Screws 18 ft. lbs.
Clutch Cover to Flywheel Bolts 40 ft. lbs.
Coil Bracket to Block Bolts 192 in. lbs.
Connecting Rod Nuts 33 ft. lbs.
Cylinder Block Drain Plugs 25 ft. lbs.
Cylinder Head Bolts 100 ft. lbs.
Cylinder Head Cover Bolts 85 in. lbs.
Differential cover 30 ft. lbs.
Differential cover 30 ft. lbs.
Differential fill plug 25 ft. lbs.
Differential fill plug 25 ft. lbs.
Distributer Clamp Bolt 204 in. lbs.
Drag link Ball studs 55 ft. lbs.
Drag Link clamp 20 ft. lbs.
Driveshaft to axel 14 ft. lbs.
Driveshaft to Transfer case 20 ft. lbs.
Engine Mounts - Front Support Bracket Bolts 45 ft. lbs.
Engine Mounts - Front Support Cushion Bolts/Nuts 30 ft. lbs.
Engine Mounts - Front Support Cushion Bracket Bolts 40 ft. lbs.
Engine Mounts - Front Support Cushion Bracket Stud Nuts 30 ft. lbs.
Engine Mounts - Front Support Cushion Thru-Bolt 48 ft. lbs.
Engine Mounts - Rear Crossmember-to-Sill Bolts (Automatic) 30 ft. lbs.
Engine Mounts - Rear Insulator Stud Assembly Nut 30 ft. lbs.
Engine Mounts - Rear Support Cushion/Bracket Nuts (Manual) 55 ft. lbs.
Engine Mounts - Rear Support Cushion/Crossmember Nuts 192 in. lbs.
Exhaust Manifold/Pipe Nuts 20 ft. lbs.
Flywheel to Converter Housing Bolts 28 ft. lbs.
Flywheel to Crankshaft Bolts 105 ft. lbs.
Front Cover-to-Block Bolts ?-20 60 in. lbs.
Front Cover-to-Block Bolts 5/16-18 192 in. lbs.
Fuel Rail Bolts/Stud 108 in. lbs.
Gas Tank Skid to frame 11.5 ft. lbs.
Gas Tank straps 3 ft. lbs.
Generator Fixed Bolt 18 ft. lbs.
Generator Thru Bolt/Nut 28 ft. lbs.
Lower Control Arms (Front) @ Axle 85 ft. lbs.
Lower Control Arms (Front) @ Frame 130 ft. lbs.
Lower Control Arms (Rear) @ Axle 130 ft. lbs.
Lower Control Arms (Rear) @ Frame 130 ft. lbs.
Main Bearing Brace Nuts 35 ft. lbs.
Main Bearing Cap Bolts 80 ft. lbs.
Oil Filter 156 in. lbs.
Oil Filter Adapter Bolts 75 ft. lbs.
Oil Filter Connector (to adapter) 35 ft. lbs.
Oil Filter Connector (to block) 50 ft. lbs.
Oil Galley Plug 30 ft. lbs.
Oil Pan ?-20 Bolts 84 in. lbs.
Oil Pan 5/16-18 Bolts 132 in. lbs.
Oil Pan Drain Plug 25 ft. lbs.
Oil Pump Cover Bolts 70 in. lbs.
Oil Pump Long Attaching Bolts 204 in. lbs.
Oil Pump Short Attaching Bolts 204 in. lbs.
Pitman Arm nut 185 ft. lbs.
Power Steering Pump Pressure Hose Nut 38 ft. lbs.
Rocker Arm Assembly-to-Cylinder Head Capscrews 21 ft. lbs.
Shock Mounts (Front) @ Lower mount 21 ft. lbs.
Shock Mounts (Front) @ Upper mount 17 ft. lbs.
Shock mounts (Rear) @ Lower mount 74 ft. lbs.
Shock Mounts (Rear) @ Upper mount 23 ft. lbs.
Spark Plugs 27 ft. lbs.
Spedo Sensor 20 in/lbs
Starter Motor Mounting Bolts 33 ft. lbs.
Steering stabilizer @ Draglink 55 ft. lbs.
Steering stabilizer @ frame 55 ft. lbs.
Sway Bar (Front) @ Lower mount 70 ft. lbs.
Sway Bar (Front) @ Upper mount 45 ft. lbs.
Sway Bar (Front) retaining bolts top 40 ft. lbs.
Sway Bar (Rear) @ Lower mount 40 ft. lbs.
Sway Bar (Rear) @ Upper mount 40 ft. lbs.
Thermostat Housing Bolts 156 in. lbs.
Throttle Body Bolts 90 in. lbs.
Tie Rod clamps 20 ft. lbs.
Tie Rod end (ball stud) 65 ft. lbs.
Tie Rod end (to hub) 55 ft. lbs.
Track Bar (Front) @ Axle 55 ft. lbs.
Track Bar (Front) @ Frame 110 ft. lbs.
Track Bar (Rear) @ Axle 74 ft. lbs.
Track Bar (Rear) @ Frame 74 ft. lbs.
Track Bar Ball stud nut (Front) 65 ft. lbs.
Transfer case drain plug 15-20 ft. lbs.
Transfer case fill plug 15-20 ft. lbs.
Transfer case front yolk 150 ft. lbs.
Transmission drain plug 14-20 ft. lbs.
Transmission fill plug 14-21 ft. lbs.
Transmission Support Adapter Bracket Bolts (2WD Auto) 55 ft. lbs.
Transmission Support Bracket Bolt (Manual) 34 ft. lbs.
Transmission Support Bracket/Cushion Bolt (4WD Auto) 55 ft. lbs.
Upper Control Arms (Front) @ Axle 55 ft. lbs.
Upper Control Arms (Front) @ Frame 55 ft. lbs.
Upper Control Arms (Rear) @ Axle 55 ft. lbs.
Upper Control Arms (Rear) @ Frame 55 ft. lbs.
Vibration Damper Bolts 80 ft. lbs.
Water Pump/Block Bolts 17 ft. lbs.
Yolk (Front) @ Axle ???
Yolk (Front) nut @ Transfer case 110 ft. lbs.
Yolk (Rear) @ Axle ???
Yolk (Rear) nut @ Transfer case 120 ft. lbs.
Yolk Straps (Front) @ axle 14 ft. lbs.
Yolk Straps (Front) @ Transfer case 20 ft. lbs.
Yolk Straps (Rear) @ axle 14 ft. lbs.
Yolk Straps (Rear) @ Transfer case ???
Click to expand...

This needs to be a sticky post somewhere... or maybe it already is -- wow!
 

https://www.helpavetshine.us/help-a-vet-shine
Top